Cooling

Touge Factory

Kswap RWD Silicone Radiator Hose Kit for TF Power Steering Kit

To make the kswap even easier for the S-chassis, we developed a reinforced silicone radiator hose kit.This version is for those of you running our hydraulic power steering kit.  The lower hose routes around the PS Pump.  This kit can be used...

Touge Factory

TF-Works RWD KSwap Lower Radiator Hose for Hydraulic PS Pump Kit

Reinforced silicone lower radiator hose for our Kswap kit.If you are running our hydraulic power steering kit, this lower radiator will route between the pump and the engine to your radiator.Includes stainless steel worm clamps.

Touge Factory

K24 / K20 Swivel Neck Coolant Thermostat Housing V2 - Ports Deleted

OEM K Series engine will have the thermostat outlet pointing towards the firewall on a RWD Swap.With the use of a swivel neck thermostat housing, it will allow you the direct the outlet in the proper orientation.This version of the swivel neck thermostat...

Touge Factory

Kswap RWD K24A2 RBB Billet Upper Coolant Neck with 1/8 Bleed Port + Speed Bleeder

The upper coolant neck sits between the rear of the engine and the firewall.This billet water neck is for the RBB / RBC (OEM K24 head) RWD K-swap setups, and our outlet tube aims forward towards the radiator.If you are using the complete K24 long block,...

Touge Factory

TF-Works RWD Kswap Water Neck with TALL Filler Tube - 15 Degree Offset

This version of our water neck has a 15 degree offset bent filler neck with even further extended height.  The filler cap is now even with the top of the valve cover.This allows for slightly more clearance away from the pinch weld and firewall. Good...

Touge Factory

TF-Works RWD Kswap Water Neck with Filler Tube

The radiator filler neck is very close to being at the same height as the water neck on the back of the cylinder head, which makes bleeding coolant on these a pain.Our standard water necks come with a 1/8 NPT Bleed port which helps, however this version...

Touge Factory

Kswap Koyo Radiator Aluminum Fan Shroud with SPAL Fans

Aluminum fan shroud with dual low profile SPAL electric fans for our K-swap Koyo radiator.Our dual pass N-Flo Koyo Kswap radiator has proven to be very effective at keeping your K20/K24 running cool, and now we have a bolt-in E-fan solution for our...

Touge Factory

1.25" (32mm) Radiator Hose DIY Kit with Aluminum Joiner + Power Grip Hose Clamp

If you're running a custom cooling setup or a chassis that requires you to piece together multiple radiator hoses to make work, this kit will allow you to make it clean and easy  for your K-swap.Rather then using a standard 32mm pipe, this is a...

J's Racing

J's Racing Shizuki Project High Pressure 1.3kg Radiator Cap - Type B

In order to get raise the effciency of the cooling system, a high pressure radiator cap is the most inexpensive to do it. J's Racing offer high pressure radiator cap at 1.3kg and cooling efficiency will be improved by 22 percent or higher. Type S is...

J's Racing

J's Racing High Pressure 1.3kg Radiator Cap - Type S

In order to get raise the effciency of the cooling system, a high pressure radiator cap is the most inexpensive to do it. J's Racing offer high pressure radiator cap at 1.3kg and cooling efficiency will be improved by 22 percent or higher. Type S is...

TracTuff

TracTuff K-Series Thermostat 5/8" Hose Barb Port Adapter Kit

TracTuff K Series Thermostat Port Adapter is the ONLY solution for those of you looking to retain in-cabin heat with some of my swirl tanks and/ or crazy sidewinder turbo manifolds that conflict with the OEM hard-pipe. It's also going to be a popular...

TracTuff

TracTuff RBB/RBC Swirl Pot - V3 W / - 16 Male Flare

TracTuff RBB/RBC Swirl Pot V3  - 16 Male Flare  - 1/8 NPT Tank Accessory Bung    A duplicate of the super popular V1SR swirl tank I made for the PRB/ PRC cylinder head is now available for the RBB/ RBC cylinder...